Reservoir Heads

From Hyrel3D
Jump to: navigation, search

储水头是365现金买球如何打印(也称为直接墨水书写或Robocasting)与流体或乳化(非丝状基)材料沉积在, above, 或者低于室温, 有或没有UV交联.

诺森和维世科的负责人

caption
一些客户要求365现金买球配置365现金买球的设备的方式,从其他公司的头,如 诺信Ultimus V头 or one of the Viscotec Vipro heads.

Yes, Hyrel设备可以容纳这些和其他打印头,只需一点定制代码和一个特殊的工具架. 如果您有任何问题,请365现金买球.

点击图片查看大图.

水头物料

油库水头的用途如下:

  • 用浆糊,凝胶,乳化剂或蜡.
  • 在室温或高温下.
  • 有或没有紫外线交联.
  • With Hyrel Nozzles (1.5mm, 2mm) or Luer Tips.

以下材料可以从冷流头打印. 请注意,粘性更大的材料可能不适合塑料注射器或较小的鲁尔针头.

以下材料可以从暖流喷头打印. 请注意,粘性更大的材料可能不适合塑料注射器或较小的鲁尔针头, 或者在更高的温度下更容易打印.

Reservoir Heads

环境沉积或亚环境沉积可透过以下水头提供:

可透过以下水塘水头进行加热沉淀:

EMO-Type头比较
Temperature > 20°C < Ambient Ambient Up to 50°C Up to 90°C Up to 180°C Up to 270°C
Crosslinking
Optional
RSD-30 EMO-25
SDS-5, -10,
SDS-30, -60
SMH-2
HSD-30 HSD-10
VOL-25
KRA-15
KR2-15
TAM-15

注意,RSD-30将带你约20C低于环境.

那么,这些愚蠢的名称到底代表什么呢?

EMO:室温下的乳化剂-低至中粘度
COD:室温乳化,按需交联,低至中粘度
VOL火山:加热(高达100°C)乳化剂-低至中粘度
KR2: Krakatoa v2:一个更强大的KRA头部与双衬垫柱塞更热, 更粘稠的乳化物-非常高的粘度
TAM:坦博拉:加热(高达270°C)乳化剂-高粘度
SDS:注射器分配系统(在室温下使用一次性塑料注射器)-低粘度
HSD:加热(以前火山式)注射器分配系统-低至中粘度
RSD:制冷注射器分配系统-低至中粘度
DSD:双注射器分配器,按固定比例分配两部分混合物-低至中粘度
SMH: Static Mixing Head, 混合你的材料比例通过折流板喷嘴-低至中粘度

引用Hyrel水库水头的研究论文

这些现在是按年列出的 here.

水库头的固件版本

列出固件信息 on our Firmware page.

用作水塘水头的水塘

这些年来,365现金买球使用了不同的水库. Here are the details.

Metal Reservoirs

Metal Reservoirs
Tube Material Plunger
O-Rings
Nominal
Volume
ID
mm
OD
mm
Default
Heads
Also
Compatible
Notes
Aluminum 1 25 cc 16.9 mm 20.2 mm EMO, VOL EMO-XT Modified "Makin"
Stainless 1 15 cc 17.7 mm 20 mm KRA* none Modified "Makin"
Stainless 1 25 cc 17.7 mm 20 mm none EMO, VOL, EMO-XT Modified "Makin"
Stainless 2 15 cc 18 mm 20 mm KR2, TAM, EMO-XT none Custom

Plastic Reservoirs

Plastic Reservoirs
Default
Heads
Tube Material Manufacturer Part
Number
Nominal
Volume
Notes Hyrel Part Quantity
SDS-1 Polypropylene MHC Easy-Touch 802010 1 cc none AN.SYR-01/100-MHC 100
SDS-5 Polypropylene BD 309646 5 cc none AN.SYR-05/125-BD 125
SDS-10 Polypropylene BD 309604 10 cc none AN.SYR-10/100-BD 100
SDS-30
SDS-30XT
Polypropylene BD 302832 30 cc none AN.SYR-30/54-BD 54
SDS-60
SDS-60XT
Polypropylene BD 309653 60 cc none AN.SYR-60/40-BD 40
SDS-150XT Polypropylene - - 150 cc none AN.SYR-150/10 10
HSD-10 Polyamide Ardes* 10 cc *modified AN.SYR-10-Ardes 1

水塘水头设置

2020年1月1日之后发货的所有打印机和打印机头都已随版本4发布, 这些值如下所示.

旧的设置在这里列出.

emo型磁头的一些设置(如温度, 质数/非质数值)将有所不同, 这取决于你用什么材料打印. 喷嘴直径应该准确地反映你所装载的喷嘴(1.默认为6mm)和你切片的路径宽度. 温度命令将被没有温度控制的头忽略. 话虽如此,下面是365现金买球的默认发货设置:

METAL Reservoir Heads

金属罐储水头的默认设置
Settings EMO, VOL
27:1 Ratio
VOL
51:1 Ratio
EMO-XT, KR2, TAM
100:1
KR2-ST
Super Torque
EMO-300XT
eXtra Torque
Material
Type Custom Custom Custom Custom Custom
Color (any) (any) (any) (any) (any)
Nozzle 1.600 1.600 1.600 1.600 1.600
Layer (any) (any) (any) (any) (any)
Temp Info
Print Temp 0 0, 35 35 (varies) 0
Power Factor 100 100 100 100 100
Minimum 0 0 0 0 0
Maximum 0 90 0 / 180 / 270 0 0
Overrides
Pulses / µL 271.9 517 1297  ?  ?
Note: Values above in BOLD 已通过多次样品测试验证,2020年7月.
Multiplier 1 1 1  ?  ?
Prime
Steps 6000 1000 6000  ?  ?
Rate 10,000 10,000 10,000  ?  ?
Dwell Time (ms) 600 100 600  ?
Unprime
Steps 6000 1000 6000  ?  ?
Rate 10,000 10,000 10,000  ?  ?
Dwell Time -600 -100 -600  ?  ?
Offsets
X 0,000 0,000 0,000 0,000 0,000
Y 0,000 0,000 0,000 0,000 0,000
Z 0,000 0,000 0,000 0,000 0,000
Head Info
Model EMO-25 VOL-25 KR2-15 or TAM-15 (varies) EMO-300XT
PCB Type 4988/160J 4988/160J 4988/160J 4988/160J 4988/160J
RTD Type 1k_PRTD 1k_PRTD 1k_PRTD 1k_PRTD 1k_PRTD
Plot Settings (any) (any) (any) (any) (any)
Motor Settings
Step Mode 16th 16th 16th 16th  ?
Motor Current Normal Normal Normal Normal  ?
Max Jog Rate 5,000 10,000 15,000  ?  ?
Rot Speed 1,500 1,500 10,000  ?  ?
Settings EMO, VOL
27:1 Ratio
VOL
51:1 Ratio
EMO-XT, KR2, TAM
100:1
KR2-ST
Super Torque
EMO-300XT
eXtra Torque

塑料储液头:表1

塑料储液器储液头的默认设置-表1:标准扭矩, Single Reservoir
Settings SDS 1 ET SDS 5 SDS 10 SDS/HSD/RSD 30 SDS 60
Material
Type Custom Custom Custom Custom Custom
Color (any) (any) (any) (any) (any)
Nozzle 1.600 1.600 1.600 1.600 1.600
Layer (any) (any) (any) (any) (any)
Temp Info
Print Temp 0 0 0 0 0
Power Factor 100 100 100 100 100
Minimum 0 0 0 0 0
Maximum 0 0 0 0 / 75 / -10 0
Overrides
Pulses / µL 270 87.3 58.7 26.8 17.4
Note: Values above in BOLD 已经通过多个样本测试验证,是2020年7月还是2021年10月.
Multiplier 1.000 1.000 1.000 1.000 1.000
Prime
Steps 3000 1500 3000 2250 1500
Rate 10,000 10,000 10,000 10,000 10,000
Dwell Time (ms) 300 150 300 225 150
Unprime
Steps 3000 1500 3000 2250 1500
Rate 10,000 10,000 10,000 10,000 10,000
Dwell Time -300 -150 -300 -300 -300
Offsets
Clone Head Off Off Off Off Off
X 0,000 0,000 0,000 0,000 0,000
Y 0,000 0,000 0,000 0,000 0,000
Z 0,000 0,000 0,000 0,000 0,000
Head Info
Model SDS SDS-5 SDS-10 SDS-30 / HSD-30 / RSD-30 SDS-60
PCB Type 4988/160J 4988/160J 4988/160J 4988/160J 4988/160J
RTD Type None None None 无/ 1k_PRTD / 1k_PRTD None
Plot Settings (any) (any) (any) (any) (any)
Motor Settings
Step Mode 16th 16th 16th 16th 16th
Motor Current Normal Normal Normal Normal Normal
Max Jog Rate 10,000 10,000 10,000 10,000 10,000
Rot Speed 1500 1500 1500 1500 1500
Settings SDS 1 ET SDS 5 SDS 10 SDS/HSD/RSD 30 SDS 60

塑料储液头:表2

塑料储层的储水头的默认设置-表2:更高扭矩和双储层
Settings HSD-10-Ardes SDS-30-XT SDS-60-XT SDS-150-XT DSD-50
Material
Type Custom Custom Custom Custom Custom
Color (any) (any) (any) (any) (any)
Nozzle 1.600 1.600 1.600 1.600 4.00
Layer (any) (any) (any) (any) (any)
Temp Info
Print Temp 35 0 0 0 0
Power Factor 100 100 100 100 100
Minimum 0 0 0 0 0
Maximum 75 0 0 0 0
Overrides
Pulses / µL 1800 86 29.1 12.8 20
Note: Values above in BOLD 已通过多次样品测试验证,2020年7月.
Multiplier 1.000 1.000 1.000 1.000 1.000
Prime
Steps 9000 1125 1500 1500 1
Rate 10,000 10,000 10,000 10,000 10,000
Dwell Time (ms) 900 115 150 150 1
Unprime
Steps 9000 1125 1500 1500 1
Rate 10,000 10,000 10,000 10,000 10,000
Dwell Time -900 -300 -300 -300 -100
Offsets
X 0,000 0,000 0,000 0,000 0,000
Y 0,000 0,000 0,000 0,000 0,000
Z 0,000 0,000 0,000 0,000 0,000
Head Info
Model (varies) (varies) (varies) (varies) (varies)
PCB Type 4988/160J 4988/160J 4988/160J 4988/160J 4988/160J
RTD Type 1k_PLAT_RTD None None None None
Plot Settings (any) (any) (any) (any) (any)
Motor Settings
Step Mode 16th 16th 16th 16th 16th
Motor Current Normal Normal Normal Normal Normal
Max Jog Rate 10,000 10,000 10,000 10,000 10,000
Rot Speed 7,500 1,500 1,500 1,500 1,500
Settings HSD-10-Ardes SDS-30-XT SDS-60-XT SDS-150-XT DSD-50